Table of Contents
- 1 Does WLC has all the features of an AP?
- 2 How does AP connect to WLC?
- 3 What are the features of WLAN controllers?
- 4 Is a WLC a Layer 3 device?
- 5 What is the responsibility of a secondary WLC 350 401?
- 6 How do I disable SSO in WLC?
- 7 When is a soldier eligible for a promotion?
- 8 Do You Lose Your promotion if you leave the Army?
Does WLC has all the features of an AP?
The 5508 WLC has no AP limit per port, but it does recommend using more than one gigabit port if supporting greater than 100 APs. The more ports you load balance your traffic over, the fewer bottlenecks you will encounter from this link.
How does AP connect to WLC?
From the CAPWAP responses received from WLCs, AP selects a WLC to join….
- AP issues a DHCP discover request to get an IP address, unless it has previously configured static IP.
- AP send a layer 3 local broadcast(255.255.255.255) message to find a WLC.
- DHCP Option 43 in the DHCP offer messages.
What is SSO in WLC?
The new High Availability (HA) feature (that is, AP SSO) set within the Cisco Unified Wireless Network software release version 7.3 and 7.4 allows the access point (AP) to establish a CAPWAP tunnel with the Active WLC and share a mirror copy of the AP database with the Standby WLC.
What protocol is used between APs and WLC?
Control and Provisioning of Wireless Access Points (CAPWAP) is a standard and interoperable protocol that enables a Wireless LAN Controller (WLC) to manage access points (AP) or wireless termination points (WTP). CAPWAP is based on the Lightweight Access Point Protocol (LWAPP).
What are the features of WLAN controllers?
A WLAN controller manages wireless network access points that allow wireless devices to connect to the network. What a wireless access point does for your network is similar to what an amplifier does for your home stereo.
Is a WLC a Layer 3 device?
WLC Platforms The WLC appliances connect to the wired network over an 802.1Q trunk; the integrated controllers support Layer 2 connections internally and can use Layer 2 or Layer 3 connections to the wired network.
How do I manually add AP to WLC?
Manually Configure Lightweight AP to join WLC
- Configure a temporary WLC with the same name and IP Address of the WLC I want my APs to join.
- Utilise DHCP Option 43 to ensure a cross-subnet discovery is available.
- Manually set the Controller IP address via the CLI.
How do I access my WLC GUI?
You can use either the service port interface or the management interface to access the GUI. You can use both HTTP and HTTPS when using the service port interface. HTTPS is enabled by default and HTTP can also be enabled. The default IP address to connect to the service port interface is 192.168.
What is the responsibility of a secondary WLC 350 401?
What is the responsibility of a secondary WLC? A. It enables Layer 2 and Layer 3 roaming between itself and the primary controller.
How do I disable SSO in WLC?
LAB: Disable AP-SSO
- Give it new management IP address (As it shares the same IP with active standalone box now) -> config interface address management
- Turn on the ports -> Config port adminmode all enable.
- Reboot the WLC -> save config -> reset system.
Is CAPWAP a Layer 3?
Control and Provisioning of Wireless Access Points protocol (CAPWAP) communications between the controller and lightweight access points are conducted at Layer 3.
Is CAPWAP a TCP?
[RFC 5418] Control And Provisioning of Wireless Access Points (CAPWAP) Threat Analysis for IEEE 802.11 Deployments….Description:
| Protocol suite: | TCP/IP. |
|---|---|
| Working groups: | capwap, Control And Provisioning of Wireless Access Points. |
| Links: |
When is a soldier eligible for a promotion?
When a soldier is pending a decision in the Disability Evaluation System, he or she remains eligible for promotion consideration, selection and promotion. A soldier with a permanent profile of 3 or 4 is not a determining factor for promotion eligibility.
Do You Lose Your promotion if you leave the Army?
Before this change, anyone who left the active component and transfer to the Reserve would lose their promotional status, said Sgt. Maj. Tim Stanton, the Army Reserve’s G-1 (personnel) sergeant major.
Can a soldier leave the Army for the Army Reserve?
Promotable soldiers leaving the active Army for the Army Reserve will bring with them not just their promotion status but their promotion points as well, Stanton said.
When do you Lose Your E5 stripes in the Army?
• Soldiers who receive a battlefield promotion to sergeant, but who are not a graduate of SSD-1, must complete the course within 270 days after redeployment (for Regular Army soldiers) or release from active duty (for National Guard and Army Reserve soldiers) to retain their E5 stripes.
https://www.youtube.com/watch?v=quiwcmEZnao